 |
| The Making of Mhondoro |
|
| I was approached by Alistair Roper of Sun International to show him some of my work with a view to me doing the trophies for the Nedbank Million Dollar Golf Tournament. I sat up late at night working on three lionesses - one landing, one running and one taking off. I caught the plane from Harare to Jo'burg with my three lions in my suitcase ready to meet with Alistair only to be told that he wanted a male lion. So I caught the plane back and started again... | |
| |
|
 |
Origination This is the origination model which was approved, and I set about making 'Mhondoro'. |
| Silicon Rubber
Mould After approval, I made a two piece mould and plaster jacket. Five years ago, my moulds were so poor due to lack of knowledge and experience that I would end up spending two days on each wax and the moulds, just tidying them up. Time has taught me that concentrating on the quality of the mould will result in minimal attention on the wax models themselves. |
 |
 |
Making of the
Wax Model
|
| Attaching of
Sprues On completion of the wax model, sprues need to be attached. This is an art in itself. Every founder has a different method. The fat rods allow the bronze to feed the model and the thin ones allow the gases to escape. Trial, error and a lot of 'short runs' later - my sprues always allow the bronze to go somewhere - there are no dead ends. A patch from the side of the lion is removed so that the slurry can coat the inside as well as the outside. The patch is sprued to the side of the tail so it can be made along with the rest of the lion and attached by welding at the end of the process. |
 |
 |
Making the
Ceramic Mould Dipping into colloidal silica slurry - the secret here is not too thick and not too thin and sprinkle with silica sand. The picture shows Amos dipping the mould. |
| The Ceramic
Mould with Wax still inside Nine coats later produces a ceramic shell sufficiently thick to withhold the molten bronze. |
 |
 |
Burning out of
the Wax This is the melting away of the wax. This must be a hot and quick process. A New Zealand friend of mine holds the shell in one hand and the gas torch in the other – this entails too much risk of being burned, so I prefer an oil drum and a large gas torch - a lot safer! |
| Empty Ceramic
Shell Once all the wax is burned out, you have an empty shell. The ceramic shell now has a void where the wax was and thus this method of casting is known as the 'lost wax technique'. |
 |
 |
Melting the
Bronze The bronze is melted in a crucible in the centre of a coke furnace. Gas, paraffin, diesel or induction furnaces can also be used. |
| Pouring the
Bronze This is always exciting no matter how many times you do it. The orange-red molten metal in the crucible is lifted from the furnace and put in the basket and then poured into the shells, which are bedded firmly into sand. If the bronze keeps pouring and the mould does not fill up - panic, you have a crack! The bronze is running out into the sand. |
 |
 |
Mould Removal Now the boring bit - removing the ceramic mould from the cooled bronze. This is done by painstakingly removing the ceramic with a hammer and chisel and must be done without marking the bronze. |
| Sprue Removal The sprues need to be removed. This is done by carefully using an angle grinder ensuring no flat edges are left behind. Final touch ups include fettling with air tools, small tips, wire brushes and sand blasting. |
 |
 |
Welding The clean bronze is now welded to close any holes (intentionally there for the drying process when making a ceramic mould). The patch on the side is replaced and the lion welded to the base. Again, fettling is done on the newly welded areas. |
| Patenating The finished bronze is wire brushed and patenated with acid to give it the desired colour. |
 |
 |
The Finished
Bronze The bronze is polished, then attached to a wooden base and named.. |
| The Making of Mhondoro |
|
|
[ Home
] [ About
] [ Gallery
] [ Sculpture Making
] [ Downloads
] [ Contact
] [ Testimonials
] [ Courses] |